Western Instruments N88-5M-I Reaching Magnetic Pit Depth Gauge, Inch Dial Indicator, 4.75" Blade, Two Magnetic Cartridges, for Measuring Corrosion and Material Loss



Price: $ 699.00

Western Instruments N88-5M Reaching Magnetic Pit Depth Gauge 4.75" Blade
Western Instruments Pit Gauges assure compliance with vessel, pipeline, tank and OCTG specifications for corrosion and erosion depth measurement.
Measuring Range: 0.0-0.5" (0.0 - 12.7 mm)
Resolution: 0.001" (0.01 mm)
Dial Diameter: 1.4" (35.5 mm)
4.75" (121 mm) Blade
Available with dial or digital indicators

Western Instruments Pit Depth Gauges allow the Corrosion Inspector to conveniently measure Pit Depth or material loss in areas of Weight-Loss Corrosion.Various Blades for the Pit Gauges are available for different applications, including the Bridging Pit Gauge which permits Inspectors to Span or Cantilever over large areas of Weight-Loss Corrosion, to get a true measure of Pit Depth


line
Kit Contents
line

  • Western Instruments N88-5M Reaching Magnetic Pit Gauge
  • 4.75" (121mm) Blade c/w Two(2) magnet cartridges
  • Operator Instructions
  • Carrying Case


line
Features
line

Zeroing Dial Indicator

  • The vertical position of the Contact Point, needs to be Zeroed with respect to the Knife Edge of the Blade.
  • Zeroing can be accomplished in two ways; by adjusting the Height of the Dial Indicator in the Blade; or by Rotating the outer Bezel Scale while pressing on the Plunger onto a flat surface.

Scale Zeroing
  • To quickly check the Zero Point of the Dial indicator, place the Blade on a representative smooth surface.
  • Gently press the Plunger, until the contact point touches the surface.
  • While the contact point is on the surface, loosen the Bezel Lock, and rotate the Bezel Scale until it reads '0' with respect to the pointer.

Height Zeroing
  • Loosen the Fastener(s) holding the Dial Indicator in place.
  • Hold the Blade firmly on a Flat Surface, and gently press the body of the Dial Indicator down until the contact point touches the flat surface.
  • Carefully re-tighten the Clamp Fastener(s) or the Set Screw.
  • Any fine zeroing can be done by rotating Bezel Scale on the Indicator.
  • Height Zeroing should be done, whenever the unit is put into to use.

Zeroing a Digital Indicator
  • Digital Indicators can be Height Zeroed or Positioned in the same way as a Mechanical Dial Indicator.
  • To Zero the Digital Indicator simply press the Zero Button when the Contact Point is on a reference point. If the Digital Indicator is Height Zeroed, press Zero when the Plunger is fully retracted.
  • To select Metric or Imperial Measurement, simply press the mm/in Button.Whennot in use, press the On/Off Button to turn the Indicator off.

Indicator Positioning
  • The position (or rotation) of the Dial indicator can be changed by simply loosening the Clamp Fasteners or Set Screw, and rotate the Dial Indicator about the Blade.
  • After the Dial Indicator is rotated, the unit should be Dial Zeroed.


line
Specifications
line

Dial and Digital Indicators

Metric Dial IndicatorRange:
Resolution:
Dial Diam.
0.0-12.7 mm
0.01 mm
35.5 mm
Imperial Dial IndicatorRange:
Resolution:
Dial Diam.
0.0-0.5"
0.001"
1.4"
Digital IndicatorRange:
Dial Diam.
0.0-0.5"
0.0-12.7 mm
56 mm, 2.2"

Measuring Corrosion (Depth)

1-Standard Tip0.040" diam.#1 Contact Point-Standard N88-S
2-Conical Tip0.010" diam.#2 Contact Point-Conical N88-C
3-Needle Tip0.005" diam.#3 Contact Point-Needle N88-N

* Western offers a variety of Contact Points, which are all 0.625" (16mm) long. Any ADG Contact point can be used with our specialdial indicators, but a different length may affect Height Zeroing, or the vertical position of the Dial Indicator. Contact Points are easily replaced, by extending the Contact Point , and turning it counter clockwise.


line
Related Products
line

N88L-1
Tri-Gauge Pit Gauge

  • Lever Type Pit Gauge for Evaluation of Corrosion
related

line

N88-2
Basic Pit Gauge Center Mount 2.5" (64 mm) Blade

  • N88-2 Basic Pit Gauge Center Mount 2.5" (64 mm) Blade
related

line

N88-3
Basic Plus Pit Gauge Centre Mount 3.5" (89 mm) Blade

  • Measuring Ranges x Resolution: 14mm x 0.01mm, 0.550 x 0.001 inch
related

line

N88-3M
Basic Plus Magnetic Pit Gauge

  • Centre mount c/w Two(2) magnet cartridges. 3.5" (89mm) Blade
related

line

N88-4
Pocket Pit Gauge

  • Dual Edge Blade (reversible). 1.5" (38mm) long and spot base
related

line

N88-5
Reaching Pit Gauge
  • 4.75" (121mm) Blade. End Mount Dial Indicator with Nose Cutout
related

line

N88-6
Reaching Plus

  • 6" (152mm) Blade. End Mount Dial Indicator with Nose Cutout.
related

line

N88-6M
Reaching Plus Magnetic Pit Gauge

  • 6" (152mm) Blade c/w Two(2) magnet cartridges.
related

line

N88-12
Reference Pit Gauge
  • 5.5 (140mm) long, 0.75 (19mm) wide with inverted V Edge, 2 magnet cartridges. Similar and interchangeable with Bridging Pit Gauge Main Blade.
related


line
Downloads
line

Western Instruments N88-5M Reaching Magnetic Pit Gauges 4.75" (121 mm) Blade - Literature
Western Instruments N88-5M Reaching Magnetic Pit Gauges 4.75" (121 mm) Blade - Data Sheet

Order Online
Check the items you would like to order then click "Add To Cart". Items typically ship within 1 Week
Product Price
Western Instruments N88-5M-I Reaching Magnetic Pit Depth Gauge, Inch Dial Indicator, 4.75" Blade, Two Magnetic Cartridges, for Measuring Corrosion and Material Loss $699.00
Accessories Price
N88-S Contact Point, Standard Tip #1 $17.00
N88-C Contact Point, Conical Tip #2 $17.00
N88-N Contact Point, Needle Tip #3 $50.00
N88-X Contact Point Extension $61.00
N88-AC Magnet Cartridges $22.00
Fasteners and Wrench Kit $28.00
N88-I Imperial "Inch" Dial Indicator $99.00
N88-M Metric Dial Indicator $110.00
N88-D Digital Inch/Metric Indicator $215.00

 



 
 

Powered by Marctin Web Architecture